Cloud phones with real local technicians — Phoenix metro only📞 (480) 397-2627
Home › Help & Guides › PoE for phones, cameras and Wi-Fi
Cabling and network

Power over Ethernet for Phones, Cameras and Wi-Fi

One cable can power a phone, a camera or an access point — if the switch, the cable and the device are sized for each other.

Power over Ethernet (PoE) sends power and data on the same structured-cabling run. That is why a desk phone, a camera or a Wi-Fi access point can come up from a single jack, with no separate power brick at the device. It only works if the switch (or injector), the cable, and the device all agree on how much power is available.

PoE types, in plain numbers

StandardCommon namePower at the switch (PSE)Power at the device (PD)Typical use
IEEE 802.3afType 1 / PoE15.4 W12.95 WMany desk phones and some basic cameras
IEEE 802.3atType 2 / PoE+30 W25.5 WMany cameras and some access points
IEEE 802.3btType 3 / PoE++ (4PPoE)60 W51 WHigher-power cameras and many Wi-Fi 6/6E access points
IEEE 802.3btType 4 / PoE++ (4PPoE)90 W71.3 WHighest-power access points and specialty devices

Figures are the IEEE 802.3 maximums at the power sourcing equipment (the switch or injector) and at the powered device after cable loss. A real device may draw less; a real budget should leave headroom. Always check the device's published power class.

Why the cable still matters

  • Voltage drop and heat. Power is lost as heat in the cable, especially in large bundles and in warm ceilings. A higher category and a well-installed link leave more usable power at the far end. Cat6A is usually the better choice for high-power access points and dense camera runs; see Cat6 vs. Cat6A vs. Cat8.
  • Distance. Ethernet and PoE still have to live within the 100 m channel limit for office copper (and 30 m for Cat8). A long, marginal run can be the reason a camera or AP reboots.
  • The whole channel. A poor patch cord, a damaged jack or an untested existing drop can drop a PoE device even when the switch budget looks fine.

Switch budget vs. a midspan injector

A PoE switch is the usual choice when you have many phones, cameras or access points: one place to manage power, VLANs and ports. Add up the published draw of the devices, then leave headroom for growth and for the fact that some devices draw more at boot. A midspan injector can power one or a few devices on a non-PoE switch, but it is easy to outgrow and easy to hide in a messy closet. For a closet that already needs work, see rack cleanup.

Phones, cameras and Wi-Fi are not the same draw

Many desk phones are happy on Type 1 or Type 2 power. Cameras vary widely with pan-tilt, heaters and IR. Current indoor and outdoor Wi-Fi access points, especially Wi-Fi 6E and Wi-Fi 7 models, often need Type 3 or Type 4. We size the switch and the cable to the devices you actually plan to install, rather than assuming every jack is a low-power phone port.

Planning phones and cameras on the same switch? That is common, and it is one reason C13 designs cabling, switching and the phone system together. Call (480) 397-2627 or get an estimate.
Not sure, or short on time? Call C13 at (480) 397-2627 or email us at [email protected], and we'll walk you through it or make the change remotely.

Questions we hear a lot

Can we run cameras and phones on the same PoE switch?

Yes, if the switch has the port count, the power budget and the right PoE type for the hungriest device, and if the network design (VLANs, for example) is thought through. We plan that on the site walk.

Will Cat5e carry PoE?

Often yes for lower-power devices on a tested link. High-power access points and dense bundles are a better fit for Cat6A. We test existing cable before we rely on it.

The camera keeps rebooting. Is that PoE?

It can be: an undersized injector, a long or damaged cable, or a switch that is out of budget. It can also be the camera, the switch port or the network. We will check the whole path rather than guessing.

Related guides

Related services: Structured cabling · Security cameras & access · UniFi installer · Business Wi-Fi · Service areas

Need a hand from a local technician?

C13 serves Phoenix-metro businesses only, so when a phone call or remote change won't fix it, a C13 technician can come to your office. Commercial clients only.

Requests sent outside business hours (Monday–Friday, 8:00 AM–5:00 PM Arizona time, closed on holidays) are handled as after-hours work and billed at 1.5x our standard hourly rate; holidays and emergencies are billed at 2x. We respond within 2 to 4 hours after your email is read. For an emergency, email [email protected] with EMERGENCY in the subject line, or call (480) 397-2627.

Last reviewed November 2026. Product names and trademarks belong to their respective owners; C13 is an independent service provider.

📞 CallInstant QuoteLogin